Buffer Amplifiers

THE DESIGN PRINCIPLES OF BUFFER AMPLIFIERS

What exactly is a buffer amplifier, what is its purpose in life?

This class of amplifier is designed to follow low level stages, one example is a crystal oscillator. An oscillator for optimum performance can NOT be loaded down, it needs an intermediate stage following. This will then present a sufficiently high enough input impedance so it is not considered a significant load to the oscillator. The intermediate or buffer stage, while not representing a load must then have a sufficiently low output impedance to drive successive stages.

If these concepts of impedance confuse or worry you then look at my other page "what is impedance?" it's a rough and ready explanation, but hopefully you will come back with a considerably better understanding.

From what I said above, two desirable traits of a buffer amplifier are high input impedance and low output impedance. Obviously succeeding stages should also be linear because we don't want to introduce distortion.

As a matter of interest a buffer amplifier is not solely limited to following an oscillator. You could have a requirement of wanting to sample the output of the first mixer for what is called a "Panadaptor", a means of visually seeing adjacent signals on an oscilloscope. Also a high quality agc system should be derived from the last i.f. stage, it should be buffered before going to the agc amplifier and then on to the agc detector.

Other examples are low level outputs of audio amplifier stages such as microphone inputs where the microphone is a high impedance type. Although not so common now, phono inputs to audio ampliers also needed buffering.

A PRACTICAL EXAMPLE

Here I'm going to use a very practical example where one of my readers has a requirement for a voltage controlled oscillator operating at 1.8 - 2.0 Mhz (amateur radio band 160M). This is to be part of a frequency synthesizer.

The design requirements were:-

(a) frequency coverage 1.8 - 2.0 Mhz

(b) voltage controlled by a frequency synthesiser with an output level sufficient to drive the input of a Phase Locked Loop (PLL)

(c) a further buffered output for a digital frequency readout.

(d) another buffered out put to drive succeeding amplifier stages.

We can look at two types of active devices for use in buffer amplifiers, FET transistors and bipolar transistors. Choice is largely a matter of opinion but more often it depends on what you have on hand. Bipolar types are referred to as "emitter followers".

Let's look again at our previous oscillator.

schematic of hartley oscillator
Fig 1.

Now it is considered bad practice to use the output of the oscillator to drive succeeding stages because in loading down the oscillator we cause frequency pulling and a host of other unwanted maladies

schematic of buffer amplifier
Fig 2.

That's about as basic as it gets. The FET represents a high input impedance (Z) but a relatively low output impedance. This buffer amplifier configuration, called a "source follower", is capable of high power gain, perhaps as much as 25 db BUT the voltage output would be only around 90% of the input which is a voltage gain of -0.5 dB (loss)

Confused?. Look at it this way - consider an input signal of say 50 mV RMS. I've just said the output voltage is about 90% or in this case 45 mV, yet I spoke of Power Gain, in fact 25 dB perhaps. Assume for purposes of discussion only, that the input impedance is 100K or 100,000 ohms.

It follows that input power taken from the preceding stage is P = E2 / R or [ ( 0.05V * 0.05V ) / 100,000 which equals 0.025 micro-watts.

If the output power available to the succeeding stage is assumed to be sourced from a relatively low 270 ohms source, albeit at a reduced voltage of 45 mV RMS, then our calculations are P = E2 / R or [ ( 0.045V * 0.045V ) / 270 this equals 7.5 micro-watts.

It further follows that for 7.5 uW output after a 0.025 uW input there must have been a power gain of 7.5 / 0.025 = 300 which 10 * log (300) = 24.77 or say 25 dB.

I am not saying this is the case. I am merely highlighting the capability and the basic underlying principles.

NEXT - Amplifier Design to boost signal levels to around 17 dBm or 50 mW



This Web page was last updated on Friday September 21, 2001


© 2000 Designed by Colin McCord